Amprobe AM-34 Auto-Digital-Multimeter User Manual download pdf

AM-34

3 3/4 DIGIT AUTO DIGITAL MULTIMETER

OPERATION MANUAL

SAFETY RULES

λ This meter is designed and tested in accordance with IEC publication 1010, pollution

degree II and installation category (overvoltage category) III 600V.

λ This meter has been tested according to the following EC Directives

♦ 89/336/EEC (EMC of Nov., 1992, Electromagnetic Compatibility)

♦ 73/23/EEC (Product safety law of June 11, 1979, Low Voltage Directive of

February 19, 1973)

λ This meter is designed to be indoor use at temperature 41°F to 104°F (5°C to 40°C)

and altitude up to 2,000m.

λ To ensure that the meter is used safely, follow all safety and operating instructions in

this operation manual. If the meter is not used as described in this operation manual,

the safety features of this meter might be impaired.

λ Do not use the meter if the meter or test leads look damaged, or if you suspect that the

meter is not operating properly.

λ When using the probes, keep your fingers behind the finger guards on the probes.

λ Disconnect the live test lead before disconnecting the common test lead.

λ Make sure power is off before cutting, unsoldering, or breaking the circuit. Small

amount of current can be dangerous.

λ Do not apply more than 600Vdc or 600Vac rms between a terminal and earth ground.

λ To avoid electrical shock, use CAUTION when working above 60Vdc or 25Vac rms.

Such voltages pose a shock hazard.

λ Never make measurements with the battery cover or bottom case off.

λ To avoid electrical shock or damage to the meter, do not exceed the input limits.

INTERNATION SYMBOLS

Important information Diode

see manual Continuity

AC Ground

DC Double insulation

FEATURES

λ One rotary switch operation.

λ Auto polarity with engineering units annunciator

λ Dual polarity A-D converter.

λ Auto voltage ranges selection: DCV: 1mV - 600V, ACV: 1mV - 600V

λ Auto ampere ranges selection: DCA: 40mA - 10A, ACA: 40mA - 10A

λ Auto resistance ranges selection: 0.1Ω - 40MΩ

λ Diode & continuity test

3.1 General Specifications

Display : 3 3/4 digit LCD, 3999 counts with decimal point and

engineering units annunciator display

Polarity : Automatic, (-) negative polarity indication.

Zero adjustment : Automatic.

Measuring Method : Dual slop integration A to D converter system.

Over range indication : Only the “OL” is displayed.

Power : Two, standard 1.5 volt (AAA) battery, UM4 or equivalent.

Dimension : 70 (H) x 144 (W) x 40 (D) mm.

Weight : Approx. 280gm. (including batteries and packaging)

3.2 Electrical Specifications

Accuracies are ± (% of reading + number of least significant digits) at 23°C ± 5°C, <75% RH.

DC Voltage Range Resolution Accuracy Input

Impedance

Overload

Protection:

4V 1mV

40V 10mV ±(0.8%+1) 10MΩ 600V DC/AC rms

600V 1V

AC Voltage Range Resolution Accuracy Frequency

(Hz)

Input Impedance:

10MΩ

4V 1mV Overload

40V 10mV

±(1.2%+3)

40-400

Protection:

400V - 600V 1V ±(1.5%+5) 40-100 600V rms

DC Current Range Resolution Accuracy Input resistor

10A 10mA

±(1.8%+5) 0.01Ω

Overload

Protection:

AC Current Range Resolution Accuracy Input resistor

10A 10mA

±(3.0%+5) 0.01Ω

10A/600V fuse

Resistance Range Resolution Accuracy Measurement

Voltage/Current

Response time:

5 sec. max. on

400Ω 100mΩ VDDA 1.2mA or

less

40MΩ range

3 sec. on all other

4kΩ 1Ω

0.7V(TYP)

0.7mA or less

range

Temperature range

40kΩ 10Ω for 40MΩ from

400kΩ 100Ω

0.47V(TYP)

18°C to 30°C

4MΩ 1kΩ

±(1.0%+2)

0.7mA or less

40MΩ 10kΩ±(1.5%+2)

Diode Test Range Resolution

0~3.999V 1mV

Open short or Normal Range

Continuity Range Resolution

Test 400Ω 100mΩ

Buzzer sound generation resistance

_50Ω

PANEL DESCRIPTIONS

1) 3 3/4 digit LCD display

2) Continuity test

3) Resistance range

4) AC voltage range

5) DC voltage range

6) Power off

7) Rotary switch

8) Data hold / power resume button

9) Case

10) Diode range

11) DC current range

12) AC current range

OPERATION WARNING

1) When measuring voltage ensure that the instrument is not connected or switched to a

current or resistance or temperature or to the diode check/continuity range. Always ensure

that the correct terminals are used for the type of measurement to be made.

2) Use extreme care when measuring voltage above 50V, especially from sources where

high energy exists.

3) Avoid making connections to “live” circuits whenever possible.

4) When making current measurements ensure that the circuit is not “live” before opening it

in order to connect the test leads.

5) Before making resistance measurements or continuity / diode test, ensure that the circuit

under test is de-energised.

6) Always ensure that the correct function and range is selected. If in doubt about the correct

range, start with the highest and work downwards.

7) Extreme care should be taken when using the instrument to conjunction with a current

transformer connected to the terminals. High voltage may be produced at the terminals if

an open circuit occurs.

8) Ensure that the test leads and prods are in good condition with no damage to the

insulation.

9) Take care not to exceed the over-load limits as given in the specifications.

10) Fuse for replacement must be of the correct type and rating.

5.1 DC and AC Voltage measurement

1) Connect the black test lead to the “COM” socket and red test lead to the “ ” socket.

2) Set the selector switch to DC V or AC V position and connect the test prods across the

source or load under measurement.

5.2 DC and AC Current measurement

1) Connect the black test lead to the “COM” socket and red test lead to the “10A” socket for

measurement up to 10A.

2) Set the selector switch to the DC current or AC current position.

3) Connect the prods in series with the current source to be measured.

5.3 Resistance measurement

1) Connect the black test lead to the “COM” socket and red test lead to the “ ” socket.

2) Set the selector switch to resistance Ω position.

3) Connect the prods across the circuit to be tested.

CAUTION: Ensure that the circuit to be tested is “dead”.

Max. input over-load : 600V rms < 10sec.

5.4 Diode test

1) Connect the black test lead to the “COM” socket and red test lead to the “ ” socket.

2) Set the selector switch to position.

3) Connect the black and red test prods to the cathode (-) and anode (+) ends of the diode to

be tested respectively.

4) Read the forward voltage drop (junction) value from the display. If reverse connected the

prods to diode, display shows over-load.

5.5 Continuity test

1) Connect the black test lead to the “COM” socket and red test lead to the “ ” socket.

2) Set the selector switch to position.

3) Connect the prods across the circuit to be tested, if the resistance less than approx. 50Ω,

buzzer will be activated.

5.6 Data hold

A push switch at the middle of rotary switch is used to hold data during measurement.

Pressing the key, reading is held and “H” appears on display. Resume active reading by

pressing switch gently once.

5.7 Auto power off

The meter will turn off automatically to extend the battery life after approx. 15 minutes without

operation. Resume power by pressing data hold push switch gently once.

6. MAINTENANCE

CAUTION

BEFORE ATTEMPTING BATTERY AND FUSE REMOVAL OR REPLACEMENT,

DISCONNECT TEST LEADS FROM ANY ENERGISED CIRCUITS TO AVOID SHOCK

HAZARD.

6.1 Fitting and replacing the battery and fuse

1) Ensure that the instrument is not connected to any external circuit, set the selector switch

to OFF position and remove the test leads from the terminals.

2) Remove the screw of the back case.

3) Replace the spent battery or fuse with the same type and rating.

4) Reinstate the back case, tighten and securing screw.

6.2 Cleaning

Periodically wipe the case with a soft damp cloth and mild household cleanser. Do not use

abrasives or solvents. Ensure that no water gets inside the equipment to prevent possible

shorts and damage.

FOR TECHNICAL ASSISTANCE,

PLEASE CONTACT:

AMPROBE

Tel : 305-423-7500

Fax : 305-423-7554

Technical Support : 800-327-5060

Summary of Contents

Page 1 - Fax : 305-423-7554

AM-34 3 3/4 DIGIT AUTO DIGITAL MULTIMETEROPERATION MANUALSAFETY RULESλ This meter is designed and tested in accordance with IEC publication 1010, pol

Comments to this Manuals

No comments

Amprobe AM-34 Auto-Digital-Multimeter User Manual

Browse online or download User Manual for Measuring instruments Amprobe AM-34 Auto-Digital-Multimeter. Amprobe AM-34 Auto-Digital-Multimeter User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Measuring instruments Amprobe AM-34 Auto-Digital-Multimeter